Reciprocating Air Compressor Oil: What to Use and How Often to Change It

Reciprocating air compressor oil does four jobs at once inside a piston machine: it seals, cools, cleans and reduces wear. Which oil you use, and how often you change it, decides how well it keeps doing all four.

Anglian Compressors, a Branch of Atlas Copco Compressors, has looked after compressed air systems from Peterborough since 1977. This guide covers what the oil has to do, why the manufacturer’s specification comes first, why unapproved motor oil doesn’t belong in a compressor and how site conditions shorten the change interval.

Use the compressor oil type and grade your manufacturer specifies, and change it at the scheduled interval, sooner in hot, dusty or humid conditions.

In This Guide

  • What compressor oil does in a piston machine
  • Choosing the type and grade
  • Why unapproved motor oil is the wrong answer for air compressors
  • How often to change the oil, and what ageing oil does
  • How to add oil between changes
  • Oil, water and downstream air quality
  • Frequently asked questions

What Compressor Oil Does in a Piston Machine

Compressor oil is a base oil stock blended with synthetic, semi-synthetic or non-synthetic additives. Besides lubricating and absorbing heat, it protects the machine against corrosion, contamination and premature wear. If you want the mechanism first, our explainer on what a piston compressor is walks through the cylinder, valves and crank.

The additive package is what separates a compressor lubricant from a general-purpose oil. It gives the oil oxidation resistance, viscosity at low temperatures, air release, demulsification, anti-foaming and anti-wear properties.

Each of those matters on a piston machine:

  • Anti-oxidants delay oxidation and the acids it forms, and protect the machine during standby periods.
  • Anti-foam additives deal with air bubbles above 1 mm in diameter, which rise and form foam. Foam exposes more oil to oxygen and speeds up oxidation.
  • Demulsifiers help water separate from the oil, so the machine is protected from water/oil emulsions and the condensate is easier to treat.

Choosing the Type and Grade From the Specification

Every compressor type needs a specific lubricant, in the same way a vehicle manufacturer specifies the type and grade of oil for its engines. Start with the instruction book for your exact model, not a similar machine on the same site. A product approved for a rotary screw isn’t automatically approved for a piston unit.

Each combination of equipment, application and conditions is unique, so the lubricant has to suit the oil circuit rather than be taken off the shelf. Our guide to choosing the right oil for your compressor covers the wider range of compressor lubricants.

How Temperature Changes the Oil

Cold oil thickens. Base oil can turn waxy or form gels, some additives stop working, and the higher viscosity causes start-up problems and blocks small lubrication channels.

Heat does the opposite damage. It speeds up oxidation, producing acids, varnish and sludge, and it can make base oil fractions bond together so the oil thickens. At very high temperatures the oil can crack thermally, and its volatile fractions escape.

Mild, Demanding and Extreme Duty

Atlas Copco grades the conditions for its rotary screw oils by temperature, humidity and dust in its compressor oil selection criteria:

ConditionsNot humid, not dustyHumid or dustyHumid and dusty
Element outlet below 95°C or ambient below 30°CMildMildDemanding
Element outlet 95-105°C or ambient 30-40°CDemandingDemandingExtreme
Element outlet above 105°C or ambient above 40°CExtremeExtremeExtreme

These thresholds are for rotary screw elements, so don’t apply them to a piston crankcase directly. What carries across is the method: heat, humidity and dust together decide how hard the oil is worked.

Why Unapproved Motor Oil Is the Wrong Answer for Air Compressors

“Can I use motor oil in my air compressor?” is one of the questions Atlas Copco answers in its guidance on choosing compressor oil. Its answer is that generic lubricants are made for a broad range of unrelated equipment with undemanding lubrication needs, so they lack the properties compressors need.

Compressor manufacturers work with oil companies to develop additive packages for their own machines. The wrong lubricant can shorten the machine’s service life, leave deposits in the oil circuit and on moving parts, and starve bearings and oil pumps of lubrication. A non-genuine lubricant can also weaken the sealing function and corrode metal parts.

The costs build from there. A deposit-filled oil circuit raises internal pressure, moving parts stop working properly and energy consumption rises. In the worst case, the result is element failure and total breakdown.

How Often to Change Reciprocating Compressor Oil

Change the oil at the interval in your manufacturer’s service schedule, and earlier when heat, dust, humidity or heavy load age it faster.

Atlas Copco lists five factors that decide when its oil-injected screw compressors need fresh oil: operating hours, oil type, compressor load, oil filtration and environmental conditions. On a piston machine, the service schedule for your exact model is the basis for the interval. Running beyond the specified drain interval to stretch the oil adds to the risks of oil ageing, which come from temperature, humidity and dust.

Site Conditions That Bring the Change Forward

Intake air quality and humidity matter as much as running hours:

  • Dust. A cement works is a dusty environment compared with an automotive plant. Dust mixes with oil to form sludge, while clean air lets oil keep its properties for longer.
  • Humidity. Water in the oil causes rust and weakens lubrication. Water also speeds up oxidation, and even dry sites can see condensation during shutdowns.
  • Load and heat. Higher loads may need more frequent changes, and hot running speeds up oxidation.

If your compressor serves a dusty process on a manufacturing site, check the oil and the intake together.

What Ageing Oil Does to the Machine

Ageing oil shows itself through the damage it causes:

  • Thicker oil, from oxidation and polymerisation in hot running or from low temperatures
  • Varnish and sludge, which clog filters and attach to the oil circuit
  • Water in the oil, which brings rust and faster oxidation
  • Deposits in the oil circuit, which raise internal pressure and energy consumption

If any of these turn up at a service, follow the manufacturer’s guidance on draining early.

Fresh oil treats the symptom. If the cause is a hot room, a damp intake or a dusty process, the new charge will age just as quickly.

Topping Up: When to Add Oil Between Changes

Top up with the same specified oil that is already in the machine. Mixing in whatever is in the stores risks an oil the manufacturer never approved, with the deposit and lubrication problems that follow. Our guide to air compressor maintenance shows where top-ups and oil changes sit in the wider service routine.

Follow the manufacturer-approved top-up procedure for your exact model, including how to make the machine safe before opening the filler. Record every top-up so the pattern is visible.

If you’re topping up more often than you used to, treat that as a fault to investigate. Oil is going somewhere, and the cause needs finding before the next charge goes in.

Oil, Water and Downstream Air Quality

An oil-lubricated compressor puts some oil into the compressed air and its condensate. Demulsifying additives help water separate from that oil, which makes oil capture and condensate disposal easier. If oil downstream is the real concern, our comparison of oil and oil-free air compressors sets out the trade-offs.

Air purity is specified against BS EN ISO 8573-1, which sets the contaminants and purity classes for compressed air. ISO 8573-2 covers measuring oil aerosol and ISO 8573-5 covers oil vapour.

Where a process needs Class 0 air, for example on electronics production lines that specify it, the required purity class should drive the compressor and treatment choice.

Piston Compressor Servicing From Anglian Compressors

Our servicing packages put oil changes on the schedule your manufacturer sets, and our engineers carry out repairs when the oil points to a deeper fault. As a Branch of Atlas Copco Compressors, we supply Atlas Copco branded spare parts and service kits.

Oil changes don’t cover statutory duties. In Great Britain, PSSR 2000 (the Pressure Systems Safety Regulations 2000) requires a Competent Person to examine the parts in your Written Scheme of Examination (WSE) at its set intervals, and we provide WSE support separately.

We work within 150 miles of Peterborough. If your piston compressor’s oil is ageing faster than it should, talk to our service team.

Frequently Asked Questions

Which Oil Is Used in an Air Compressor?

An oil-lubricated air compressor uses a dedicated compressor oil of the type and grade its manufacturer specifies, because every compressor type needs a specific lubricant. Whether that is a mineral oil or a synthetic is set by the specification too. Our team provides the approved lubricant and service kits for the machines we maintain, and can confirm the right oil for your model.

Can I Use 10W30 in an Air Compressor?

No, unless the compressor’s instruction book names it. 10W30 is a motor oil grade, and generic lubricants lack the additive properties a compressor needs. Anglian Compressors offers the specified compressor oil and can drain a machine that has had motor oil added.

Can I Use 15W40 in My Air Compressor?

Not unless the compressor’s manufacturer approves it. The wrong lubricant can leave deposits in the oil circuit, starve bearings and oil pumps of lubrication and shorten the machine’s life. Our team provides oil checks during servicing if you’re unsure what is in the compressor.

Can I Use 20W40 for an Air Compressor?

Only if it is the lubricant named in your instruction book. A grade chosen for an engine isn’t approved for a compressor, and compressor manufacturers develop their own additive packages with oil companies. Anglian Compressors offers the approved lubricant for the compressors we service.