Rotary Screw Compressor Oil: Types, Grades and Change Intervals

Rotary screw compressor oil is specified for the machine in the same way an engine oil is specified for a vehicle, down to its type, grade and change interval. Every type of compressor needs its own lubricant, and the right one depends on the equipment, the application and the conditions in your compressor room.

At Anglian Compressors, a Branch of Atlas Copco Compressors, we service oil-injected rotary screw machines with the fluid their element was designed around. This guide covers the oil types, grades and change intervals, and the signs that the oil is ageing faster than the plan assumes.

What the Oil Does in an Oil-Injected Element

In an oil-injected screw element, the oil is part of the compression process. It does five jobs at once:

  • Cooling: it carries away the heat of compression. Run the element too hot and the rotating parts are overstressed, which shortens their service life.
  • Lubrication: it stops metal-to-metal contact between the rotors, which would otherwise lead to early breakdown.
  • Sealing: it closes the clearance between the rotors and the housing so the element compresses efficiently.
  • Cleaning: it traps contaminants that come in with the intake air.
  • Noise reduction: it acts as a sound barrier inside the element.

Lose one of those functions and the others suffer with it. The manufacturer’s guidance is that generic lubricants and irregular maintenance cut the machine’s lifetime, performance and energy efficiency.

Rotary Screw Compressor Oil Types

A compressor lubricant is a base oil stock blended with synthetic, semi-synthetic or non-synthetic additives. The base oil provides lubrication and heat absorption. The additive package tailors the fluid to the equipment and the ambient conditions.

The Additives That Matter

Anti-oxidant additives delay oxidation and the formation of acids. They extend the oil’s life and protect the machine during standby periods.

Anti-foam additives deal with air bubbles above 1 mm in diameter, which rise and form foam. Foam exposes more oil to oxygen and saturates the oil separator if left unchecked.

A saturated separator raises the pressure drop, and every 1 bar of pressure drop adds 7% to energy consumption.

Demulsifying additives help the oil release water rather than form an emulsion. That makes oil capture from the condensate easier further down the line.

The Roto Fluid Range

For oil-injected Atlas Copco GA rotary screw compressors, the specified fluids sit in the Roto range. Three appear on the manufacturer’s oil selection chart:

  • Roto Inject NDURANCE (part number 1630114600): a mineral-based oil formulated for GA-GX rotary screw machines. It is rated against the fewest combinations of condition and oil lifetime.
  • Roto Synthetic ULTRA (part number 1630204105): a synthetic fluid rated against more combinations than the mineral oil, with some marked as partial coverage.
  • Roto Xtend Duty: rated against the widest spread of conditions and lifetimes of the three, so it is the one to look at first for long intervals or harsh rooms.

The chart tells you which fluids are rated for your conditions. It can’t tell you which one costs least per running hour on your site, because that depends on your duty cycle and service plan.

Oil-free machines are a different case. A closed-circuit oil-free compressor keeps oil out of the compression chamber but still has an oil circuit to specify, often running higher hours under greater loads. Our overview of the ZT 30-50 VSD+ oil-free compressors explains how those machines are built.

Compressor Oil Grades: Viscosity Grade and Operating Class

When engineers search for a compressor oil grade, they usually mean the viscosity grade on the drum. That comes from the lubricant your compressor’s manufacturer specifies for the element, so start with the equipment specification rather than a generic number. The manufacturer’s oil selection criteria then add an operating-condition class, which decides whether a specified fluid suits your site and how long it lasts.

Three conditions set the class:

  • Temperature: measured at the element outlet or as ambient temperature in the compressor room.
  • Dust: a cement works is a dusty environment, while an automotive plant is expected to be clean. Dust mixes with oil and forms sludge.
  • Humidity: moist intake air brings water into the oil, causing rust and weakening lubrication. Even in a dry room, condensation can form during shutdowns.

Combine them and you get one of three classes:

Temperature bandHumid or dusty?Class
Element outlet below 95°C or ambient below 30°CNeither, or one of the twoMild
Element outlet below 95°C or ambient below 30°CBothDemanding
Element outlet 95°C to 105°C or ambient 30°C to 40°CNeither, or one of the twoDemanding
Element outlet 95°C to 105°C or ambient 30°C to 40°CBothExtreme
Element outlet above 105°C or ambient above 40°CAnyExtreme

The class is not fixed for the life of the machine. A room that is never both humid and dusty, and sits below 30°C ambient in winter, moves from Mild to Demanding in a summer that takes it into the 30°C to 40°C band, on the same machine and the same oil.

Why Viscosity Changes as the Oil Ages

Viscosity matters, but it moves as the oil ages. In cold conditions the base oil turns waxy or forms gels, and the rising viscosity causes start-up problems and blocks small lubrication channels.

Heat-related oil degradation can increase viscosity too. Polymerisation joins smaller fractions of the base oil together and raises the viscosity. That’s why the specified grade is a starting point, and the class decides how long it holds.

Change Intervals: 2,000, 4,000 or 8,000 Hours

The selection chart rates each Roto fluid against recommended oil lifetimes of 2,000, 4,000 and 8,000 running hours within each class. A fluid rated for a long lifetime in Mild conditions may carry a shorter rating, or none, in Extreme conditions.

The manufacturer lists five factors that decide when the oil needs replacing:

  • Operating hours: how long the compressor has been running.
  • Oil type: different oils have different lifespans.
  • Compressor load: higher loads may call for more frequent changes.
  • Oil filtration: whether the oil filter is maintaining oil quality.
  • Environment: high temperature, dust and humidity may call for more frequent changes.

A year contains 8,760 hours, so a machine running 24 hours a day, 7 days a week reaches 8,000 running hours in under a year. The input people get wrong is the class, so recheck the selected fluid’s rated lifetime whenever the conditions in the room change.

Stretching the interval looks like a saving. The manufacturer’s guidance is direct: running equipment longer than the specified oil drain interval adds to the risks of oil ageing.

Warning Signs the Oil Is Ageing Early

High temperatures speed up oxidation, producing acids, varnish and sludge. Water accelerates oxidation too, and attacks metal components that then speed up the reaction further.

Look for these between services:

  • Clogged oil filters or separator elements: sludge made of oxidised oil, metals and other impurities attaches to the oil circuit.
  • A rising pressure drop across the separator: a saturated element adds energy cost every hour the machine runs.
  • Foam in the oil: foam exposes more oil to oxygen and accelerates oxidation.
  • Higher element outlet temperatures: a machine running hotter than it used to may have moved into a harder class.
  • Hard starts from cold: thickened oil and blocked lubrication channels show up first at start-up.

On an oil-injected machine, a daily oil level check reduces wear from friction. Oil filter and separator inspections belong with air filter checks and controller testing in routine maintenance, and replacement filters, separators and service parts can be ordered online.

Keeping Oil Out of the Air and the Drain

The oil separator removes oil from the compressed air before it leaves the machine. Where the process needs cleaner air, dryers and filters downstream reduce the oil content further, against the purity classes in BS EN ISO 8573-1.

Oil also ends up in the condensate, which is where the demulsifying additives earn their place. A fluid that separates cleanly from water makes capture in the oil-attracting bags of an oil-water separator easier.

Our UK guide to oil-water separators covers condensate treatment in detail.

Frequently Asked Questions

Can I Use 10W30 in an Air Compressor?

No. We don’t recommend 10W30 or any other engine oil in a rotary screw compressor, because the element was designed around a specific compressor lubricant and its additive package. Use the fluid the manufacturer specifies, since generic lubricants harm the machine’s lifetime, performance and energy efficiency.

How Does a Rotary Screw Air Compressor Work?

A rotary screw compressor is a positive displacement machine. Two screws turn in opposite directions, trapping air between them and reducing its volume before it passes to the receiver. With no valves in the compression process, it delivers a continuous flow of compressed air, and our comparison of rotary vane and rotary screw compressors shows how it differs from a vane design.

How Do You Remove Oil From a Compressor?

Oil is removed from the compressed air by the oil separator, with downstream filtration where the process needs it. Oil in the condensate goes through an oil-water separator before disposal. Draining and refilling the compressor oil itself belongs in a planned service, on the interval set by your operating class.

What Type of Oil Should I Use in My Air Compressor?

Use the lubricant specified for your compressor’s element, chosen for your site’s operating class. For Atlas Copco GA oil-injected machines, our team provides the Roto fluid that fits, from mineral-based Roto Inject NDURANCE to Roto Synthetic ULTRA or Roto Xtend Duty. For other compressor technologies, see our wider guide to compressor oil selection.

Get the Class and Interval Checked

Our engineers cover a 150-mile radius from Peterborough, across East Anglia, the East Midlands, Cambridgeshire, Lincolnshire and Northamptonshire. If you’re not sure which class your compressor sits in, ask us to check it and recommend the fluid and change interval that fit.

Where the separator pressure drop has already crept up, a free energy audit will show what it is costing you to run.